Remote Monitoring
Made Easy!

Introduction

RMS-200 Is a unique remote monitoring, data acquisition, and control device specifically designed for
use with Battery powered wireless internet repeater sites, or other AC & DC powered
remote equipment

RMS-200 Has ultra low power consumption and won't put a drain on your power source. Uses less than 2 watts.

RMS-200 Is powered by DC voltage from 10 to 60 volts.

RMS-200 Uses embedded Ethernet technology for internet data acquisition and remote voltage monitoring.

RMS-200 Uses the LINUX operating system for versatility, stability, and security.

RMS-200 Gives you the situational awareness you need to keep your equipment operational and reliable.

Possible Applications

AC or Battery Powered Microwave / Telephony / Network Equipment

Use RMS-200 to monitor battery levels, room temperature, signal strength (RSSI) on radios and more. RMS-200 has 6 onboard isolated voltmeters giving it the ability to measure DC voltage from -100 to +100 volts with 24 bit accuracy. RMS-200 also has 3 power relays giving it the unique ability to turn on/off devices remotely using an Internet connection. Use the power relays to remote start a generator. RMS-200 has 5 dedicated input pins used for door alarms, solar panel theft prevention, or to monitor motion sensors. RMS-200 has an on-board temperature sensor and can alert you to dangerous temperature conditions. RMS-200 has a full featured serial port, control modems, cell phones, gsm modules, and other devices that use serial communication. RMS-200 has two USB 2.0 ports that supports several USB devices concurrently using a USB hub. Control USB cameras, store data on USB flash drives, control USB speakers etc. RMS-200 has input and output pins used to control your own custom devices. RMS-200 can alert you via email or SMS messages when your battery bank is low. RMS-200 has ping monitor software that allows you to monitor network devices and alert you to failure and possibly power cycle the device. Monitor all this information remotely over an Internet connection using an ordinary web browser. RMS-200 gives you direct hardware control of fans, lights, computers, cameras, modems, radios, etc... No more guessing what your battery levels are. No more wondering if your signal strengths are at an acceptable level. No more long drives to reset a fussy radio. Let RMS-200 do this all remotely via the Internet.

RMS-200 Features
Features:

Six layer PCB with Nickel Immersion Gold plating and red solder mask.
400 - MHz Arm Processor (500 Mips !).
256 - megs of Nand Flash. Create and store custom applications.
64 - megs of SD-Ram.
Dual Low Noise Switching Power Supplies, accepts 8 - 60 vdc input. Can be powered directly from 12, 24, or 48 volt battery banks.
Battery backed-up, real time clock.
One onboard temperature sensor - 25c + 100c.
Six 24 bit isolated voltmeters (+/- 100 VDC). Each voltmeter has its own 24 bit Delta Sigma ADC.
Each voltmeter can be put into low voltage shunt mode (+/- 2 VDC).
Two Power Relays for devices using up to 240v - 5 amps AC/DC current.
One Power Relay for devices using up to 240v - 10 amps AC/DC current.
Two programmable push buttons.
Four general purpose I/O pins.
Five alarm input pins.
Power output port, 5.0vdc (500ma).
One full serial port for controlling cell phones, modems, GPRS, etc.
One console serial port for full terminal access.
Two USB 2.0 ports for cameras, wireless clients, extra Ethernet, etc.
Runs real Linux! 2.6.33 kernel.
Send SMS messages, Email alerts, SNMP traps, Remote Syslog Messages.
Ping watchdog, power cycle equipment after a set amount of ping timeouts.
Command line utilities: ping, ftp, email, relays, etc.
Flash new firmware over the internet.
Duel Watchdog Reset circuits, processor integrated, and extra hardware.
Control RMS-200 via web page, telnet, ssh, or snmp.
Full SNMP v1, v2, v3 support (default v3).
Supports external USB relays and voltmeters.
Hardware is user accessible from files on the board.
Make your own utilities and scripts to upload. (Bash, PHP, Python, Lua)
Pluggable connectors for ease of use.

A partial list of programs and packages included:
SQLlite v3 database, Telnet ,Drop Bear SSH, Light Http and Https Server, Pro FTP, Cron scheduling agent, Busy Box, PPP, Net SNMP, NanoCom, Easy Edit and Vi, Fping, SMTP email client, IPtables, Lrz and Lsz, Open SSL, Modbus Library, RRD Tool, USB Web Camera Support.

A programmers dream:
RMS-200 comes with PHP, Python, Lua, and TCL. Make your own custom monitoring programs and upload them to the RMS-200 board, or create your own branded interface! 150 megs of storage available for your programs.

For more information on how to use RMS-200 visit the Setup Page.

Put any circuit on the Internet with RMS-200! Custom built firmware software available upon request. Other hardware and software modifications available by special order. Please refer to the contacts at the bottom of this page.

Contact/Purchase:

In Canada & Overseas

EtherTek Circuits
Dan Pattison
Phone (250)295-6794
email: sales(at)remotemonitoringsystems.ca

In the United States

Invictus Networks LLC
Rick Lindahl
Phone: 503-635-2562,
email: rickl(at)invictusnetworks.com

In Australia

All Things Digital
John Burns
Phone: 08-6397-3002,
email: john(at)atdigital.com.au